SE Electronics RNR1 Rupert Neve Active Ribbon Microphone

SE Electronics RNR1 Rupert Neve Active Ribbon Microphone

Product code: seernr1

Designed and built by Mr. Rupert Neve and sE Electronics A leap in technology. The world's first HF Ribbon mic For many decades Ribbon mics have been used by engineers for their extremely natural sounding reproduction of source material. The nature of their performance differs greatly from condenser mics, which by comparison sound very 'up front' and lack the harmonic depth of a good ribbon.


  • SE Electronics RNR1 Rupert Neve Active Ribbon Microphone


    Designed and built by Mr. Rupert Neve and sE Electronics

    A leap in technology… The world's first HF Ribbon mic

    For many decades Ribbon mics have been used by engineers for their extremely natural sounding reproduction of source material. The nature of their performance differs greatly from condenser mics, which by comparison sound very 'up front' and lack the harmonic depth of a good ribbon.

    Even at the high end of the market, the customary roll-off of almost all the top end frequencies has always been a major drawback. The frustration with all ribbons is – depending on the model – little or no performance past 7-10KHz, which is why condenser mics dominate the recording market.

    Read More



    The traditional appeal of the condenser then has been the assumption of consistent frequency response from 20Hz to 20KHz. The pay-off of course is that these mics require a certain degree of circuit board magic to achieve this, since the taughtness of the diaphragm – compared with relatively slack ribbon membranes – means condensers tend to be more 'coloured' in their sound.

    Traditionally engineers using ribbons, however expensive, have had to accept their significant limitations or have had to augment the recording with a condenser mic to capture the high frequency absent from the ribbon output.

    Such compromises have meant that ribbons have never been very widely accepted or used as a first choice for recording.

    Not any more!

    Rupert Neve's new custom circuit design now allows high frequencies to be captured and output from the capsule for the first time ever in pristine detail. Standard performance of the RNR1 is an unprecedented 20Hz to 25KHz – three times the frequency range of even the best available competitor ribbon mics on the market today!

    More than this, Mr Neve's hand-wound custom input and output transformers create huge amounts of headroom and effectively lower the noise levels by using gain stages to amplify the signal. The slight dip in the frequency response from 16-25KHz in the RNR1 can therefore be effectively flattened if required, producing an almost perfectly flat response, way beyond what human ears can perceive. This is crucial in making the RNR1 by far the best performing ribbon mic in the world today.

    The RNR1's faithful reproduction of fine harmonic material across the frequency spectrum results in the unparalleled capturing of real sound. Indeed its ability to capture modulation from infinite harmonic frequencies normally masked on any recording assures its revolutionary status and exemplary reputation.

    The mics look beautiful, the packaging is second to none, and their performance will set new standards in the high-end microphone market.

    SE Electronics RNR1 Specifications

    • Acoustic Operating Principle: Electrodynamic pressure gradient with active electronics
    • Generating Element: 2.5-micron aluminum ribbon
    • Polar Pattern: Figure 8
    • Frequency Response: 20Hz - 25KHz
    • Sensitivity: -32 dB (referenced 1v/pa ±1dB)
    • Equivalent Noise Level: 15dB (A weighted)
    • Output Impedance: 200 Ohms balanced
    • Rated Load Impedance: 1000 Ohms
    • Max SPL: >135dB
    • Connector: Male XLR 3 pin (Pin 2 Hot)

  • This product will be ordered in from our suppliers as required. Please contact us for availability.

    This item is normally sent to Mainland UK addresses by DPD who generally provide a one-hour window of delivery on the morning of delivery by email or text message. If you need this item faster, please upgrade to a Before 12 service at checkout.

    FREE delivery within mainland UK

    UK Non-Mainland: £ 12

    Rep. of Ireland and Mainland Europe: from £ 15 (calculated at checkout) International orders over £250 are delivered FREE except for large or heavy items. Please see our international delivery page or contact us for details.

  • 2 Recommended Accessories

  • Related Posts

  • Additional Information

    Brand SE Electronics
    Condition New
    Specifications

    • Acoustic Operating Principle: Electrodynamic pressure gradient with active electronics

    • Generating Element: 2.5-micron aluminum ribbon

    • Polar Pattern: Figure 8

    • Frequency Response: 20Hz - 25KHz

    • Sensitivity: -32 dB (referenced 1v/pa ±1dB)

    • Equivalent Noise Level: 15dB (A weighted)

    • Output Impedance: 200 Ohms balanced

    • Rated Load Impedance: 1000 Ohms

    • Max SPL: >135dB

    • Connector: Male XLR 3 pin (Pin 2 Hot)

FeeFo Reviews

This product has no reviews yet.