Presonus Eris E8 8 inch Active Studio Monitors (Pair)
The Presonus Eris E8 monitors offer top quality studio-accurate monitoring.
- 8-inch Kevlar low-frequency transducer
- 1.25-inch, ultra-low-mass, silk-dome, high-frequency transducer
- 140 watt, Class AB biamplification
- Front-firing acoustic port for superior bass-frequency reproduction
- RF interference, output current limiting, over-temperature, transient, and subsonic protection
- Optimised, resonance-suppressing internal bracing
- Balanced XLR/¼-inch and unbalanced RCA inputs
- Read More
When you're ready to get serious about recording, it's time to step up to PreSonus Eris-series studio monitors. Cheap computer speakers and home-stereo speakers won't reveal the truth about your mix. They aren't designed for that.
In contrast, Eris speakers are real studio monitors, delivering a very accurate response with a tight bass and very clear upper end. That's what you need in a home studio. Thanks to well-designed Kevlar® low frequency transducers, low-mass silk-dome tweeters, responsive Class AB amplification, and professional acoustic-adjustment controls, Eris delivers the goods.
When Size Matters
With its 8-inch, Kevlar low-frequency transducer, driven by a 75 watt, Class AB power amplifier, the E8 can range down to 35 Hz. Like the E5, the E8 can reach all the way to 22 kHz, thanks to a 1.25-inch (32 mm), silk-dome, high-frequency tweeter. However, the E8's tweeter is driven by a heftier 65W, Class AB amplifier. With its extra juice, the E8 can deliver up to 105 dB SPL, peak.
The Eris E8 provides balanced XLR, balanced 1/4 inch TRS, and unbalanced RCA line-level inputs. When both balanced connections are in use, the TRS input will supersede the XLR input. The RCA input is summed into the signal path. With this selection, you'll have no problem hooking your Eris speakers up with virtually any line-level source.
You're in control!
Today's music producers deal with a wide variety of musical genres and often work in more than one location. It's easy to take your Eris E8 speakers with you when you want to work in a different space. It's almost as easy to customise their sound for your room and type of music.
The most basic control is the Input Gain, which determines the signal level before it reaches the power amp. This is part of gain-staging your overall system: that is, setting the levels for every part of the recording chain in order to get the optimal level of clean audio all the way through. Once you've gain-staged your system, you can leave this control alone.
The Eris E8 provides three EQ controls in its Acoustic Tuning section: High, Mid, and Low Cutoff. These controls enable you to fine-tune the monitors and even to broadly approximate the sounds of different types of speakers so you can hear what your mix might sound like, for instance, on a car stereo or portable radio. The Low control also is useful when using the E8 with a subwoofer.
In addition to the Acoustic Tuning controls, Eris speakers offer a three-position Acoustic Space switch. This switch controls a second-order, low shelving filter that cuts the level of all frequencies below 800 Hz by a specified amount (-2 or -4 dB) to compensate for the boundary bass boost that occurs when the monitor is placed near a wall or corner. If you don't want to roll off those lows, set it to 0 dB.
This combination of controls lets you create a linear response for accurate monitoring and enables you to simulate different listening environments, so you don't have to listen to mixes on your car, consumer computer speakers, and home stereo to check how the music sounds with different systems. Instead, you can adjust the Eris monitors' response and test your mixes without leaving your studio. No other monitors in this price class offer this degree of control.
Any loudspeaker is subject to an assortment of environmental and performance problems, and Eris monitors offer protection from most common of these. RF shielding protects against radio frequencies that could be induced into the signal and become audible. (If you've ever heard a radio broadcast unexpectedly coming out of a guitar amp, that's the result of RF interference.)
Eris monitors also provide over-temperature protection to avoid heat-related issues, current-output limiting (to prevent damage should there be a short circuit on the speaker terminals), and subsonic protection to filter out extremely low-frequency vibrations that could interfere with the woofer's performance.
Finally, Eris' power amplifiers have a 'soft startup' so that you don't get damaging pops in the speakers when you power them up.
Eris E8 Specifications (Per Speaker)
1- Balanced XLR
1- Balanced 1.4 inch TRS
1- Unbalanced RCA
Frequency Response: 35 Hz - 22 kHz
Crossover Frequency: 2.2 kHz
LF Amplifier Power: 75W
HF Amplifier Power: 65W
Peak SPL (@ 1 meter): 105 dB
LF Driver: 8 inch Kevlar
HF Driver: 1.25 inch silk dome
Input Impedance: 10 k ohm
Volume Range:A-type taper
MF Control: -6, 0, +6 dB
HF Control: -6, 0, +6 dB
Low Cut: Flat, 80 Hz, 100 Hz
Acoustic Space: Flat, -2 dB, -4 dB
External mains fuse
Dimensions (W x D x H): 250x 299 x 384 mm / 9.84 x 11.77 x 15.12 inches
Weight: 10.07 Kgs / 22.2 lbs.