Line 6 DT25 Guitar Amplifier Head
The Line 6 DT25 amp head features four boutique tube amps in one unit, allowing you to create your perfect tone! Whether you're after classic American clean tones or good old British crunch, class A chime or modern high-gain, the DT25 has the flexibility to deliver. You can even fine-tune each voicing of the DT25 by reconfiguring analogue components in order to create completely original tones.
- Four boutique tube amps in one unit
- Selectable analogue components
- Channel switching for instant flexibility
- Low volume mode
- Seamless integration with POD HD processors
- Cabinet-simulated direct out
- Read More
Selectable Analogue Components
Rather than being set in stone like those of most great tube amps, the analogue components at the heart of DT25 are all totally reconfigurable to match the tones in your head. Select any of the amp's four voicings (which offer the perfect combinations of negative feedback loop topology, and HD preamp and tone stack modeling), and the DT25 gives you analogue settings to match. You can further alter settings such as output tube class (A or AB), power tube mode (pentode/triode) settings and more to take your tone beyond the traditional templates.
Channel Switching for Instant Flexibility
In addition to all of its voicing flexibility, DT25 features two entirely independent channels. A flick of its A/B switch or a tap of a latching footswitch is capable of causing a full analogue and digital transformation – go from a tight, crystalline American clean to an open, jangly British crunch. Dial in two clean sounds or set one channel as a Boost. Set them any way you like – you're not forced to choose between just 'clean' and 'dirty.'
Low Volume Mode
Way beyond a traditional master volume, switching to Low Volume mode lets you take the DT25 down to whisper-quiet levels for recording or late-night jamming, without losing an ounce of your crystalline clean or bone-crunching high-gain tones. The tubes distort less in Low Volume mode so the HD modeling technology picks up the slack and fills out the tone with rich power amp modeling so it still sounds like it's cranked up even at low levels.
L6 LINK: Full Integration of Amp and Multi-Effect
DT25 amps and POD HD processors seamlessly integrate to become a boutique tube amp factory complete with a staggering collection of preamps, tone stacks and effects available at the twist of a knob or the stomp of a switch.
MIDI In and Out/Thru
With its back-panel MIDI In and Out/Thru jacks, the DT25 is primed and ready to receive all your MIDI switching commands – from simple to complex. Use any standard MIDI switching system to control channel, voicing, reverb on/off, pentode/triode mode and class A/AB selection.
Channel and Reverb Footswitch
The footswitch jack on the back of the DT25 provides some simple and incredibly useful functions. Connect any standard latching, two-button footswitch with a TRS cable for channel switching and global reverb switching. Or, for channel switching only, use a single-button footswitch connected with a TS cable.
Serial Effects Loop
The Send and Return jacks that make up the DT25 serial effects loop tap the signal chain post-preamp so you can link up your own favourite effect devices, from vintage tape delays to modern multi-effects processors like Line 6 stompbox modelers.
Multiple Speaker Outputs
A straightforward selection of speaker outputs provides a fool-proof connection to single or multiple speaker cabs without fear of an impedance mismatch. Whether it's a single 4-ohm, 8-ohm or 16-ohm cab, or two 4-ohm or two 8-ohm cabs at a time, the DT25 has clear back-panel connections that make it easy to achieve a safe match.
Cabinet-Simulated Direct Out
Go direct and get rich, juicy DT25 tone without mic'ing the speaker. Connect an XLR cable from the transformer-tapped direct out to a PA, mixer or recording interface and achieve every detail of your precious tone complete with full cab simulation. A handy ground-lift switch is included to eliminate any unwanted hum or buzz.