* SPECIAL OFFER * Focal Alpha 65 Complete Studio Monitoring System
Complete Focal monitoring solution including a pair of Alpha 65 6 inch monitors and a Presonus 10 inch subwoofer.
- System frequency response: 20Hz - 22kHz
- Low directivity: keeps the same sound throughout the room
- Tonal balance is identical at low and high volumes - low sensitivity to the wall effects
- Optimal acoustic integration
- Cables Included
- Read More
Package consists of:
• 2 x Focal Alpha 65 Active Studio Monitor, Single
• 1 x Presonus Temblor T10 Active Studio Subwoofer
• 2 x 3 metre balanced jack to Male XLR cable
• 2 x 2 metre male XLR to female XLR cable
Focal Alpha 65 Active Studio Monitors
The Focal Alpha 65 Active Studio Monitor performs just as well with instrumental music as with electronic music, and is characterised by its great versatility.
The Alpha 65 is composed of a 6.5 inch (16.5cm) woofer/ midrange speaker with a Polyglass cone loaded in a large laminar port associated to a 70W amplifier and of a 1 inch (25mm) aluminium inverted dome tweeter (35W amplifier). Alpha 65 has a frequency response of 40Hz to 22kHz (+/- 3dB).
Specifications (per speaker):
Frequency response (+/- 3dB): 40Hz - 22kHz
Power: 105W (70W+35W)
Maximum SPL: 106dB SPL (pic @ 1m)
Inputs/Connectors: XLR balanced 10kOhms, RCA unbalanced 10kOhms with sensitivity compensation
LF amplifier stage: 70W, class AB
HF amplifier stage: 35W, class AB
Standby mode: After about 30 minutes without using the monitor
Activation from Standby mode: By signal detection >3mV
Power Connection IEC inlet and detachable power cord
Sensitivity: Adjustable, 0 or +6dB
LF shelving (0 - 300Hz): Adjustable, +/-6dB
HF shelving (4.5 - 22kHz): Adjustable, +/-3dB
Power ON/OFF: Switch on rear panel
Indicators: Power ON/OFF LED, Standby LED
Woofer: 6.5 inch (16.5cm) drive unit, Polyglass cone
Tweeter: 1 inch (25mm) drive unit, Aluminium inverted dome
Cabinet Construction: 0.6 inch (15mm) MDF
Cabinet Finish: Vinyl and Black painting
Dimensions, with 4 rubber pads (HxWxD): 13.7 x 9.9 x 12.2 inches (348 x 252 x 309mm)
Weight: 20.7lb (9.4kg)
Presonus Temblor T10 Active Studio Subwoofer
The Presonus Temblor T10 is a versatile and powerful active studio subwoofer that perfectly complements any monitoring setup.
The Bottom Line Is Great Sound
To hear what's really going on at the bottom of your mixes, you need a subwoofer that speaks the truth. The Presonus Temblor™ T10 lets you take charge of the low-frequency foundation of your mix with a combination of quality components and design, plenty of inputs and outputs, and extensive user controls not normally available in this price range.
An ideal companion to Eris™ and Sceptre™ active reference monitors, the T10 complements full-range monitors without overshadowing them, extending the reach of your full-range system's low end with a musical and natural approach.
Powerful and musical, Temblor features high-quality components and design that enable it to deliver fast and accurate transient response, extending low frequencies without a hint of 'tubbiness' or overshoot.
The Temblor T10 is an active subwoofer with a 10-inch glass-composite driver, built-in crossover, high-temperature voice coil, and damped rubber surround. Its cabinet features a front-firing, bass-reflex acoustic port and optimised, resonance-suppressing internal bracing. The enclosure has integrated rubber feet for stable placement.
In addition to outstanding accuracy and a frequency response that ranges from 20 Hz to 130 Hz, this combination of features enables the subwoofer to produce higher volume—up to 113 dB SPL—with less power than a sealed-box design. But make no mistake, the T10 has plenty of juice: 250 watts of Class AB power.
The result is a subwoofer that delivers accurate, tight low end and outperforms subs costing far more. With Temblor T10, you hear what the foundation of your mix really sounds like so you can produce your best mix from top to bottom.
Customise Your System Until It's Just Right
The T10 provides more user controls than any other subwoofer in its class, enabling seamless integration into your listening environment.
The Temblor T10's extensive user controls include input gain (-30 dB to +6 dB, continuously variable) and a continuously variable lowpass filter (50 Hz to 130 Hz) that let you create a seamless crossover transition between your full-range studio monitors and subwoofer for a more accurate listening environment.
A switchable highpass filter removes frequency content below 80 Hz from the full-range signal sent from the T10 outputs to the main monitors, avoiding destructive cancellation and reinforcement in the T10's upper range.
The result is a subwoofer that can be adjusted to perfectly complement not only Sceptre™ CoActual™ and Eris™ active studio monitors but virtually any studio monitor.
The T10 also features a momentary footswitch (included) that bypasses the subwoofer, highpass filter, and Sub Out. This allows your audio source signal to pass directly through the Temblor T10 to the full-range studio monitors, making comparing your mix with or without sub frequencies quick and easy. This helps to ensure your mix will sound good on a wide variety of systems.
Of course, Presonus didn't forget the 'small things' that can make a big difference: polarity invert and a ground-lift switch.
Versatile I/O Works With Any Setup
The Temblor T10 provides a choice of three input pairs: two sets of balanced inputs (XLR and 1/4 inch TRS) and one pair of RCA unbalanced inputs. Pairs of inputs are provided in order to accept a stereo signal from your audio source.
When both of the balanced connections are in use, the TRS inputs will take precedence over the XLR inputs. The RCA inputs will sum into either balanced connection.
You get two pairs of balanced outputs: XLR and 1/4 inch TRS. The full-range signal connected to the stereo inputs on the T10 is passed through to these outputs so you can connect them to your main left and right studio monitors. If the High Pass Filter switch is engaged, frequencies below 80 Hz are not sent from these outputs.
The T10 also has a balanced XLR output that sends the low-frequency signal from the lowpass filter to a second Temblor T10 for the ultimate in smooth low end.
Presonus Temblor T10 Specifications
2- Balanced XLR
2- Balanced 1/4 inch TRS
2- Unbalanced RCA
2- Balanced XLR (full range with 80 Hz HPF option)
2- Balanced 1/4 inch TRS (full range with 80 Hz HPF option)
1- Balanced XLR (Sub Out)
Frequency Response: 20 Hz – 200 Hz
Low Pass Filter Frequency: 50 – 130 Hz (variable)
Signal-to-Noise Ratio: >98 dB
THD: 0.019% @ power <160W
Amplifier Power: 170W RMS
Power Consumption: 230W
Amplifier Type: Class AB
Peak SPL at 1m: 113 dB
Woofer: 10 inch glass-composite
Input Gain Range: -30 to +6 dB
Polarity Switch: 0° or 180°
Low Pass Filter Control: 50 Hz to 130 Hz
Ground Lift Switch: On/Off
High Pass Filter Switch: On/Off
Bypass Footswitch: On/Off
External mains fuse
Dimensions and Weight
Dimensions (W x D x H): 320 x 400 x 400 mm / 12.6 x 15.75 x 15.75 inches
Weight: 19.9 Kgs / 39.46 lbs
- This product is in stock and ready to ship
This item is normally sent to Mainland UK addresses by Interlink who generally provide a one-hour window of delivery on the morning of delivery by email or text message. If you need this item faster, please upgrade to a Before 12 service at checkout.
FREE delivery within mainland UK
UK Non-Mainland: £ 12
Rep. of Ireland and Mainland Europe: from £ 15 (calculated at checkout) International orders over £250 are delivered FREE except for large or heavy items. Please see our international delivery page or contact us for details.
4 Recommended Accessories
Brand Focal Condition New Power 101-200W
|This product has no reviews yet.|